FSA1258AL8X
| Parameters | |
|---|---|
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 20 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 1.15Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 2nA Typ |
| Channel Capacitance (CS(off), CD(off)) | 11.5pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 35ns, 15ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 40ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Height Seated (Max) | 0.55mm |
| Length | 1.6mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFQFN |
| Number of Pins | 8 |
| Weight | 25mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 1.15Ohm |
| Terminal Finish | Nickel (Ni) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BUTT |
| Number of Functions | 2 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | FSA1258 |
| Output | SEPARATE OUTPUT |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100nA |
| Power Dissipation | 180mW |
| Max Supply Current | 500nA |
FSA1258AL8X Overview
Shipping overseas is convenient due to the electrical component's packing in 8-UFQFN. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around -40°C~85°C TA extended. There are 8 terminations totally. High-quality output is provided by the electronic component's 2 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. SPST - NO/NC switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with FSA1258. Internally, this switch multiplexer has a resistance of 1.15Ohm. You can find the functions of the 8 pins in the datasheets. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The analog switch ic is of the Single supply type and is cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. A voltage of 2.7V~5.5V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
FSA1258AL8X Features
2 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 300MHz
FSA1258AL8X Applications
There are a lot of ON Semiconductor FSA1258AL8X Analog Switches & Multiplexers ICs applications.
- RGB switches
- High reliability control systems
- Data Acquisition Systems
- Precision instrumentation
- MP3 players
- Multi-Line E1 Interface Cards
- Audio/video switches
- Microprocessor controlled systems
- USB 1.1 signal switching circuits
- Signal routing between systems
