Parameters |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
400Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
QUAD |
Number of Functions |
2 |
Supply Voltage |
2.3V |
Terminal Pitch |
0.4mm |
Base Part Number |
FSA2467 |
Output |
SEPARATE OUTPUT |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
4.3V |
Min Supply Voltage |
1.65V |
Max Supply Current |
100nA |
Turn On Delay Time |
80 ns |
Supply Type |
Single |
Turn-Off Delay Time |
52 ns |
-3db Bandwidth |
85MHz |
On-State Resistance (Max) |
400Ohm Typ |
Multiplexer/Demultiplexer Circuit |
2:2 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
10nA |
Channel Capacitance (CS(off), CD(off)) |
32pF |
On-state Resistance Match-Nom |
0.03Ohm |
Switch Circuit |
DPDT |
Switch Time (Ton, Toff) (Max) |
50ns, 32ns |
Charge Injection |
15pC |
Channel-to-Channel Matching (ΔRon) |
40m Ω (Min) |
Crosstalk |
-75dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.65V~4.3V |
Height Seated (Max) |
0.55mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lifecycle Status |
LAST SHIPMENTS (Last Updated: 3 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-UFQFN |
Number of Pins |
16 |
Weight |
6.54mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2016 |
FSA2467UMX Overview
Shipping overseas is convenient with the electronic component packed in 16-UFQFN. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:2. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. Due to its 2 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 2.3V, it should be turned on and run. Unlike digital switches, these are based on DPDT switching circuits. The multiplexer consists of 2 circuits. Try searching for the analog switch ic with FSA2467 if you are looking for variants. A 400Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 4.3V. The digital multiplexer has a low cost Single supply. 1.65V is the lowest voltage the electrical component should receive. A voltage of 1.65V~4.3V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 100nA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
FSA2467UMX Features
2 Channels
Switch Circuit: DPDT
-3db Bandwidth: 85MHz
FSA2467UMX Applications
There are a lot of ON Semiconductor FSA2467UMX Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Sample hold systems
- Video switching
- Cell phones
- Wireless Local Loop
- Digital cross connects (DSX-1)
- Video signal routing
- Precision test equipment
- Microprocessor controlled systems
- Cable PC