FSA2859UCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-UFBGA, WLCSP |
| Number of Pins | 12 |
| Weight | 42mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| Resistance | 750mOhm |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Number of Functions | 1 |
| Supply Voltage | 1.95V |
| Terminal Pitch | 0.5mm |
| Base Part Number | FSA2859 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 10nA |
| Max Supply Current | 50nA |
| Turn On Delay Time | 70 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| Max Dual Supply Voltage | 5.5V |
| -3db Bandwidth | 60MHz |
| On-State Resistance (Max) | 750mOhm |
| Min Dual Supply Voltage | 1.65V |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 60 dB |
| Channel Capacitance (CS(off), CD(off)) | 50pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 25ns, 20ns |
| Charge Injection | 47pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -65dB @ 1MHz |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Length | 1.91mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
FSA2859UCX Overview
This electronic part is conveniently packaged in 12-UFBGA, WLCSP, making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. 2:2 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 12. A 2 channel electronic part produces high-quality output. An 1.95V voltage supply should allow the electrical part to be turned on and run. DPDT switching circuits are used in these analog switch ics. It consists of 2 circuits. Try searching with FSA2859 to find analog multiplexer variants. It has an internal resistance of 750mOhm. You can find the functions of the 12 pins in the datasheets. normally, users should not supply switches with voltages higher than 5.5V. Analog switch ics with Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 1.65V. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. A digital multiplexer may suffer damage if voltage is applied above 50nA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5.5V. It is recommended that you attach at least 1.65V to your dual power supply.
FSA2859UCX Features
2 Channels
Switch Circuit: DPDT
-3db Bandwidth: 60MHz
FSA2859UCX Applications
There are a lot of ON Semiconductor FSA2859UCX Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- RGB switches
- Optical Applications
- Communications systems
- Relay Replacement
- Industrial and process control systems
- Isolation
- Digital Cross-Connects
- Cell phones
- Channelized and Unchannelized DS3 applications
