Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-VFSOP (0.091, 2.30mm Width) |
Number of Pins |
8 |
Weight |
30mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2005 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
15Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
180mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Number of Functions |
1 |
Supply Voltage |
2.3V |
Terminal Pitch |
0.5mm |
Base Part Number |
FSA3357 |
Number of Outputs |
3 |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Nominal Supply Current |
1μA |
Power Dissipation |
180mW |
Max Supply Current |
1μA |
Turn On Delay Time |
6.5 ns |
Supply Type |
Single |
Bandwidth |
250MHz |
Turn-Off Delay Time |
3.7 ns |
-3db Bandwidth |
200MHz |
On-State Resistance (Max) |
15Ohm |
High Level Output Current |
128mA |
Multiplexer/Demultiplexer Circuit |
3:1 |
Off-state Isolation-Nom |
58 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
3.6pF |
On-state Resistance Match-Nom |
0.31Ohm |
Switch Circuit |
SP3T |
Switch Time (Ton, Toff) (Max) |
6.5ns, 3.7ns |
Charge Injection |
3pC |
Channel-to-Channel Matching (ΔRon) |
150m Ω |
Crosstalk |
-60dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
7.2ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Drain to Source Resistance |
9Ohm |
Height |
700μm |
Length |
2mm |
Width |
2.3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
FSA3357K8X Overview
The electrical component comes in 8-VFSOP (0.091, 2.30mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 3:1. Operation at a temperature around -40°C~85°C TA. In total, there are 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. An 2.3V voltage supply should allow the electrical part to be turned on and run. A SP3T switching circuit is used for these analog switches. FSA3357 can be used to search for analog multiplexer variants. There is 15Ohm internal resistance in this digital multiplexer. Datasheets for functions of 8 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 5.5V to a switch device. Single supply type digital switch with a low cost. 1.65V should be the lowest voltage fed to the electronic component. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. There are 250MHz bandwidths for data transfer. Resistivity from Drain to Source is 9Ohm for this electronic part. The analog switch ics has 3 outputs.
FSA3357K8X Features
1 Channels
Switch Circuit: SP3T
-3db Bandwidth: 200MHz
Bandwidth: 250MHz
Drain-to-Source resistance: 9Ohm
FSA3357K8X Applications
There are a lot of ON Semiconductor FSA3357K8X Analog Switches & Multiplexers ICs applications.
- PDAs
- Relay Replacement
- Cell phones
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Signal routing between systems
- Wireless Local Loop
- Avionics
- USB 1.1 signal switching circuits
- DSUs
- ATM