FSA4157AL6X
| Parameters | |
|---|---|
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 35ns, 15ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Height | 450μm |
| Length | 1.45mm |
| Width | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN |
| Number of Pins | 6 |
| Weight | 30g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 1.15Ohm |
| Terminal Finish | Nickel/Gold (Ni/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | FSA4157 |
| Number of Outputs | 2 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100nA |
| Power Dissipation | 180mW |
| Max Supply Current | 500nA |
| Turn On Delay Time | 60 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 20 ns |
| On-State Resistance (Max) | 1.15Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 2nA Typ |
| Channel Capacitance (CS(off), CD(off)) | 12pF |
| On-state Resistance Match-Nom | 0.06Ohm |
FSA4157AL6X Overview
Shipping overseas is convenient with the electronic component packed in 6-UFDFN. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operation at a temperature around -40°C~85°C TA. In total, there are 6 terminations. The electronic part provides high-quality output because it has 1 channels. Turning on and running the electrical part should be easy with a 4.5V voltage supply. A SPDT switching circuit is used for these analog switches. Using the FSA4157 search parameter, you can discover variants of the switch. This digital multiplexer has 1.15Ohm internal resistance. The functions of 6 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. The analog switch ic is of the Single supply type and is cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. This analogue multiplexer requires a voltage of 2.7V~5.5V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 500nA. The data can be transferred over a wide range of bandwidths, called 300MHz bandwidths. There are 2 outputs on the analogue multiplexer.
FSA4157AL6X Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 300MHz
FSA4157AL6X Applications
There are a lot of ON Semiconductor FSA4157AL6X Analog Switches & Multiplexers ICs applications.
- Modems
- SONET
- Battery Powered Instruments
- E1 Multiplexer
- Audio and video signal routing
- Audio signal routing
- Access Concentrators
- Power routing
- Frame Relay Equipment
- MP3 players
