banner_page

FSA4157AP6X

35ns, 15ns SPDT 1.15Ohm DUAL Analog Switches BREAK-BEFORE-MAKE FSA4157 2nA Typ 4.5V 6-TSSOP, SC-88, SOT-363


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-FSA4157AP6X
  • Package: 6-TSSOP, SC-88, SOT-363
  • Datasheet: PDF
  • Stock: 734
  • Description: 35ns, 15ns SPDT 1.15Ohm DUAL Analog Switches BREAK-BEFORE-MAKE FSA4157 2nA Typ 4.5V 6-TSSOP, SC-88, SOT-363(Kg)

Details

Tags

Parameters
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 3 days ago)
Contact Plating Tin
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 6-TSSOP, SC-88, SOT-363
Number of Pins 6
Weight 28mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
ECCN Code EAR99
Resistance 1.15Ohm
Subcategory Multiplexer or Switches
Max Power Dissipation 180mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Number of Functions 1
Supply Voltage 4.5V
Base Part Number FSA4157
Number of Outputs 2
Power Supplies 3/5V
Number of Channels 1
Max Supply Voltage 5.5V
Min Supply Voltage 2.7V
Nominal Supply Current 100nA
Power Dissipation 180mW
Max Supply Current 500nA
Turn On Delay Time 60 ns
Supply Type Single
Bandwidth 300MHz
Turn-Off Delay Time 20 ns
On-State Resistance (Max) 1.15Ohm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 70 dB
Current - Leakage (IS(off)) (Max) 2nA Typ
Channel Capacitance (CS(off), CD(off)) 12pF
On-state Resistance Match-Nom 0.06Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 35ns, 15ns
Charge Injection 20pC
Channel-to-Channel Matching (ΔRon) 60m Ω
Crosstalk -70dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-off Time-Max 30ns
Voltage - Supply, Single (V+) 2.7V~5.5V
Height 1mm
Length 2mm
Width 1.25mm
Radiation Hardening No

FSA4157AP6X Overview


As the electronic part is packed in 6-TSSOP, SC-88, SOT-363, international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. There are 6 terminations totally. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. A SPDT switching circuit is used for these analog switches. Try searching for the analog switch ic with FSA4157 if you are looking for variants. A 1.15Ohm internal resistance characterizes this multiplexer. To find out what the functions of 6 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. It is recommended to use 2.7V as the lowest voltage for the electrical part. An analogue multiplexer drains from a single voltage supply at 2.7V~5.5V. Putting voltage greater than 500nA on the multiplexer may cause damage. A 300MHz-bandwidth can be used for data transfer. An output of 2 is provided by the digital multiplexer.

FSA4157AP6X Features


1 Channels
Switch Circuit: SPDT
Bandwidth: 300MHz

FSA4157AP6X Applications


There are a lot of ON Semiconductor FSA4157AP6X Analog Switches & Multiplexers ICs applications.

  • Cellular phones
  • Precision test equipment
  • Data switching
  • High reliability control systems
  • Power routing
  • Audio signal routing
  • MP3 players
  • Access Concentrators
  • Channel Banks
  • Microprocessor controlled systems

Write a review

Note: HTML is not translated!
    Bad           Good