banner_page

FSA4157P6

35ns, 15ns SPDT 1.15Ohm DUAL Analog Switches BREAK-BEFORE-MAKE FSA4157 2nA Typ 4.5V 6-TSSOP, SC-88, SOT-363


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-FSA4157P6
  • Package: 6-TSSOP, SC-88, SOT-363
  • Datasheet: PDF
  • Stock: 644
  • Description: 35ns, 15ns SPDT 1.15Ohm DUAL Analog Switches BREAK-BEFORE-MAKE FSA4157 2nA Typ 4.5V 6-TSSOP, SC-88, SOT-363(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status LAST SHIPMENTS (Last Updated: 3 days ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 6-TSSOP, SC-88, SOT-363
Number of Pins 6
Weight 28mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2005
JESD-609 Code e3
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
Termination SMD/SMT
ECCN Code EAR99
Resistance 1.15Ohm
Terminal Finish Tin (Sn)
Subcategory Multiplexer or Switches
Max Power Dissipation 180mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Number of Functions 1
Supply Voltage 4.5V
Base Part Number FSA4157
Number of Outputs 2
Number of Channels 1
Max Supply Voltage 5.5V
Min Supply Voltage 1.65V
Nominal Supply Current 100nA
Power Dissipation 180mW
Max Supply Current 500nA
Turn On Delay Time 60 ns
Supply Type Single
Bandwidth 300MHz
Turn-Off Delay Time 20 ns
On-State Resistance (Max) 1.15Ohm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 70 dB
Current - Leakage (IS(off)) (Max) 2nA Typ
Channel Capacitance (CS(off), CD(off)) 12pF
On-state Resistance Match-Nom 0.06Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 35ns, 15ns
Charge Injection 20pC
Channel-to-Channel Matching (ΔRon) 60m Ω
Crosstalk -70dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-off Time-Max 40ns
Voltage - Supply, Single (V+) 1.65V~5.5V
Drain to Source Resistance 750mOhm
Height 1mm
Length 2mm
Width 1.25mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

FSA4157P6 Overview


Shipping overseas is convenient with the electronic component packed in 6-TSSOP, SC-88, SOT-363. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. A total of 6 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. Circuits based on SPDT switching are used to construct these analog switch ics. Try searching with FSA4157 if you're looking for variants. Analog switches have 1.15Ohm internal resistance. For functions related to 6 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Single supply type. There should be 1.65V voltage fed to the electrical part below 1.65V. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~5.5V. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. A 300MHz-bandwidth can be used for data transfer. Drain to Source resistance is 750mOhm. The analogue multiplexer has 2 outputs.

FSA4157P6 Features


1 Channels
Switch Circuit: SPDT
Bandwidth: 300MHz
Drain-to-Source resistance: 750mOhm

FSA4157P6 Applications


There are a lot of ON Semiconductor FSA4157P6 Analog Switches & Multiplexers ICs applications.

  • Cable Modem
  • PDH Multiplexers
  • Medical
  • Modems
  • SONET/SDH ADM
  • E1 Multiplexer
  • Industrial control systems
  • Cross Connects
  • Cell phones
  • Cable Telephony – NIU, Set-Top Box, Home Side Box

Write a review

Note: HTML is not translated!
    Bad           Good