Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
6-TSSOP, SC-88, SOT-363 |
Number of Pins |
6 |
Weight |
28mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2010 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
1.15Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
180mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Number of Functions |
1 |
Supply Voltage |
4.5V |
Base Part Number |
FSA4157 |
Number of Outputs |
2 |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Nominal Supply Current |
500nA |
Power Dissipation |
180mW |
Max Supply Current |
500nA |
Turn On Delay Time |
35 ns |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
15 ns |
On-State Resistance (Max) |
1.15Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
70 dB |
Current - Leakage (IS(off)) (Max) |
2nA Typ |
Channel Capacitance (CS(off), CD(off)) |
12pF |
On-state Resistance Match-Nom |
0.06Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
35ns, 15ns |
Charge Injection |
20pC |
Channel-to-Channel Matching (ΔRon) |
60m Ω |
Crosstalk |
-70dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
30ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Drain to Source Resistance |
1.15Ohm |
Height |
1mm |
Length |
2mm |
Width |
1.25mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
FSA4157P6X Overview
Presented in 6-TSSOP, SC-88, SOT-363, this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 2:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 6 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching for FSA4157 variants of the analog switch ic. An switch multiplexer with 1.15Ohm internal resistance has a value of 1.15Ohm. For details about the functions of 6 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 1.65V. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. It may damage the digital multiplexer if the voltage is higher than 500nA. 300MHz bandwidths enable data to be transferred. A Drain to Source resistance of 1.15Ohm is shown for this electronic part. An output of 2 is provided by the digital multiplexer.
FSA4157P6X Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 300MHz
Drain-to-Source resistance: 1.15Ohm
FSA4157P6X Applications
There are a lot of ON Semiconductor FSA4157P6X Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- USB 1.1 signal switching circuits
- Digital Cross-Connects
- DSLAMs
- E1 Network Equipment
- 65 V DACs
- Audio signal routing
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- High-Voltage
- Wireless Local Loop