FSA66P5X
| Parameters | |
|---|---|
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | FSA66 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 50nA |
| Power Dissipation | 150mW |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 7 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 9.2 ns |
| -3db Bandwidth | 250MHz |
| High Level Output Current | 128mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 125Ohm |
| Switch Circuit | SPST - NO |
| Charge Injection | 0.05pC |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 60Ohm |
| Height | 1mm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 23g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 15Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 150mW |
| Technology | CMOS |
| Terminal Position | DUAL |
FSA66P5X Overview
Packed in 5-TSSOP, SC-70-5, SOT-353, the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. There are 5 terminations totally. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. A SPST - NO switching circuit is used to build these analog multiplexers. FSA66 can be used to search for analog multiplexer variants. It has an internal resistance of 15Ohm. For details about the functions of 5 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. Putting voltage greater than 10μA on the multiplexer may cause damage. There is 60Ohm resistance between Drain and Source for this electronic part.
FSA66P5X Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 250MHz
Drain-to-Source resistance: 60Ohm
FSA66P5X Applications
There are a lot of ON Semiconductor FSA66P5X Analog Switches & Multiplexers ICs applications.
- Industrial
- Avionics test equipment
- Communication systems
- Channel Banks
- Digital access cross connects
- Access Concentrators
- Power routing
- Public switching systems
- Multi-Line E1 Interface Cards
- Optical Applications
