FSA859UCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFBGA, WLCSP |
| Number of Pins | 8 |
| Weight | 42mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 750mOhm |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Number of Functions | 1 |
| Supply Voltage | 1.95V |
| Terminal Pitch | 0.5mm |
| Base Part Number | FSA859 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 180mW |
| Max Supply Current | 50nA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| Max Dual Supply Voltage | 5.5V |
| -3db Bandwidth | 60MHz |
| On-State Resistance (Max) | 750mOhm |
| Min Dual Supply Voltage | 1.65V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 50pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 25ns, 20ns |
| Charge Injection | 70pC |
| Crosstalk | -55dB @ 1MHz |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
FSA859UCX Overview
The electronic component is convenient to ship overseas because it is packed in a 8-UFBGA, WLCSP. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 1.95V, it should be turned on and run. These analog multiplexers are built based on SPDT switching circuits. Search with FSA859 if you are looking for analog multiplexer variants. It has an internal resistance of 750mOhm. To find out what the functions of 8 pins are, please refer to their datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.65V. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 50nA. For this switch, a dual supply voltage is feasible, but it must not exceed 5.5VWith dual power supplies, you should attach at least 1.65V. Operating 1 inputs is required. The analogue multiplexer has 2 outputs.
FSA859UCX Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 60MHz
FSA859UCX Applications
There are a lot of ON Semiconductor FSA859UCX Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Avionics
- High-Voltage
- Digital access cross connects
- Sample-and-hold systems
- Video signal routing
- Avionics test equipment
- Switching Systems
- Multiplexers
- Transmit
