FT8010MPX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Weight | 6mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Reset Timer |
| Terminal Finish | Nickel/Palladium (Ni/Pd) |
| Subcategory | Analog Waveform Generation Functions |
| Max Power Dissipation | 5mW |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | FT8010 |
| Output | Open Drain, Push-Pull |
| Number of Channels | 1 |
| Max Supply Voltage | 5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5mW |
| Adjustable Threshold | NO |
| Propagation Delay | 310 ns |
| Quiescent Current | 20μA |
| Turn On Delay Time | 310 ns |
| Reset | Active High/Active Low |
| Reset Timeout | Adjustable/Selectable |
| Number of Timers/Counters | 1 |
| High Level Output Current | -500μA |
| Low Level Output Current | 500μA |
| Height | 750μm |
| Length | 2mm |
| Width | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
FT8010MPX Overview
This voltage supervisor has a total of 8 mounting terminals that can be used for mounting. Packaging is in the form of a Tape & Reel (TR). There are 1 functions included in this PMIC so that you can refer to them. This power management is made up of 1 channels which are available in a series format. There are 8-WFDFN Exposed Pad functions included in this PMIC so that you can refer to them. This IC power shares lots of benefits with other Reset Timer products. Specifies a reflow peak temperature of 260 for the package during reflow. Surface Mount mounts IC management. The power management belongs to the Analog Waveform Generation Functions subcategory. Pin count of the power management is 8. IC management can only work with a supply voltage of 1.8V volts. There should be no more than 5V volts of supply voltage (Vsup) in this power management. The recommended mounting type is Surface Mount. The temperature of the supervisors should be set to this range: -40°C~85°C TA. During operation, this power management system outputs Open Drain, Push-Pull. If you want to search for similar IC managements of this manufacturer, you can always refer to FT8010, which is the base power ics number.
FT8010MPX Features
Reset Timer type
Minimum supply voltage of 1.8V
FT8010MPX Applications
There are a lot of ON Semiconductor FT8010MPX Voltage Supervisors applications.
- Microprocessor system
- Efficient information transmission
- Smartphones
- Telecommunications equipment
- Leakage protection
- WiFi router
- Urban rail transit weak current power monitoring
- Battery-powered equipment
- Electrical fire monitoring system
- Precision measurement
