HCF4051M013TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.05kOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | MOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | HCF4051 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 80nA |
| Nominal Supply Current | 80nA |
| Power Dissipation | 500mW |
| Propagation Delay | 60 ns |
| Quiescent Current | 80nA |
| Turn On Delay Time | 720 ns |
| Logic Function | Demultiplexer, Demux, Multiplexer, Mux |
| Number of Inputs | 8 |
| Supply Type | Dual |
| Bandwidth | 60MHz |
| Supply Current-Max (Isup) | 3mA |
| Turn-Off Delay Time | 450 ns |
| On-State Resistance (Max) | 280Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.2pF 5pF |
| On-state Resistance Match-Nom | 10Ohm |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -40dB @ 3MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~20V |
| Height | 1.65mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
HCF4051M013TR Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Operating temperature extended to -55°C~125°C TA. The total number of terminations is 16. The electronic part delivers high-quality output through its 8 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 16 pins. There are 1 circuits in this switch device. Try searching for HCF4051 variants of the analog switch ic. This digital multiplexer has 1.05kOhm internal resistance. The functions of 16 pins can be found in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 20V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual supply type. A low voltage of 3V should be applied to the electronic component. The switch device would be able to operate with 80nA current. A voltage of 3V~20V is required to drain this analog switch from a single voltage supply. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. The electrical component supports 8 inputs. 60MHz bandwidths enable data to be transferred.
HCF4051M013TR Features
8 Channels
80nA Supply Current
Bandwidth: 60MHz
HCF4051M013TR Applications
There are a lot of STMicroelectronics HCF4051M013TR Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Modems
- 65 V DACs
- Digital Cross-Connects
- Sample hold systems
- SONET/SDH ADM
- Relay replacements
- New designs requiring multiplexer functions
- Fiber In The Loop (FITL)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
