HCF4067M013TR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Termination | SMD/SMT |
| Resistance | 240Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | HCF4067 |
| Pin Count | 24 |
| Polarity | Non-Inverting |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 80nA |
| Nominal Supply Current | 80nA |
| Power Dissipation | 200mW |
| Propagation Delay | 60 ns |
| Quiescent Current | 80nA |
| Turn On Delay Time | 650 ns |
| Logic Function | Demultiplexer, Demux, Multiplexer, Mux |
| Number of Inputs | 16 |
| Supply Type | Dual |
| Turn-Off Delay Time | 440 ns |
| On-State Resistance (Max) | 240Ohm |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Current - Leakage (IS(off)) (Max) | 100μA |
| Channel Capacitance (CS(off), CD(off)) | 0.2pF 5pF |
| On-state Resistance Match-Nom | 10Ohm |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -40dB @ 1MHz |
| Voltage - Supply, Single (V+) | 3V~20V |
| Drain to Source Resistance | 125Ohm |
| Height | 2.35mm |
| Length | 15.6mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
HCF4067M013TR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 24-SOIC (0.295, 7.50mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 16:1. Operation at a temperature around -55°C~125°C TA. Totally, there are 24 terminations. As a result of its 16 channels, this electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. The electronic part body is injected with 24 pins. The multiplexer consists of 1 circuits. Try searching for the analog switch ic with HCF4067 if you are looking for variants. There is 240Ohm internal resistance in this digital multiplexer. The datasheets for the 24 pins explain the functions. Multiplexers should not be powered above 20V in normal situations. Dual supply type digital switch with a low cost. 3V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 80nA. A voltage of 3V~20V is required for this switch device, which drains from a single voltage source. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. Operating the 16 inputs requires 16 inputs. There is 125Ohm resistance between the Drain and Source on this part.
HCF4067M013TR Features
16 Channels
80nA Supply Current
Drain-to-Source resistance: 125Ohm
HCF4067M013TR Applications
There are a lot of STMicroelectronics HCF4067M013TR Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Modems
- Communication systems
- PDH Multiplexers
- Relay replacements
- Sample-and-hold systems
- Ultrasound
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Digital cross connects (DSX-1)
- New designs requiring multiplexer functions
