HCPL-7800
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | HCPL-7800 |
| Output Voltage | 6V |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 10.9mA |
| Nominal Supply Current | 16mA |
| Power Dissipation | 250mW |
| Amplifier Type | Isolation |
| Common Mode Rejection Ratio | 76 dB |
| Current - Input Bias | 500nA |
| Voltage - Supply, Single/Dual (±) | 4.5V~5.5V |
| Output Current per Channel | 16mA |
| Input Offset Voltage (Vos) | 300μV |
| Bandwidth | 100 kHz |
| Rise Time | 2.96μs |
| Voltage Gain | 22.92dB |
| -3db Bandwidth | 100MHz |
| Isolation Voltage | 3.75kV |
| Height Seated (Max) | 4.7mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
HCPL-7800 Overview
Packaged in a 8-DIP (0.300, 7.62mm) case, the buffer op amp is ready to use. An op amp of this type is a Isolation-type. A Tube case is used to deliver the buffer op amp. It is estimated that there will be at least 8 terminations this year. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A total of 8 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 300μV. For this electronic part, it is recommended that you mount it with type Through Hole. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . As long as the supply current of the chip does not exceed 10.9mA, this op amp ic can operate. It is a member of the 22.92dB's 22.92dB family. In total, there are 1 circuits on this buffer amplifier. The op amp ic has 1 channels on it. The operating supply voltage of the buffer op amp is rated at 5V.
HCPL-7800 Features
supply voltage of 5V
22.92dB voltage gain
HCPL-7800 Applications
There are a lot of Broadcom Limited HCPL-7800 Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Automotive sensors
- Voltage regulation circuit
- High/low-pass filter circuit
- High input resistance broadband
- Differentiator circuits
- Subtraction operation circuits
- Industrial applications including automation
- PDA
- Instrumentation
