HEF4052BTT-Q100,11
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 175Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | 4052 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 20μA |
| Power Dissipation | 500mW |
| Propagation Delay | 5 ns |
| Turn On Delay Time | 260 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Dual, Single |
| Bandwidth | 70MHz |
| Turn-Off Delay Time | 205 ns |
| On-State Resistance (Max) | 155Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF |
| On-state Resistance Match-Nom | 25Ohm |
| Switch Circuit | SP4T |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1MHz |
| Voltage - Supply, Single (V+) | 3V~15V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
HEF4052BTT-Q100,11 Overview
This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. Increasing operating temperature to around -40°C~125°C TA. Total terminations are 16. A 8 channel electronic part produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 16 series. Unlike digital switches, these are based on SP4T switching circuits. A total of 2 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with 4052. An switch multiplexer with 175Ohm internal resistance has a value of 175Ohm. The datasheets for the 16 pins explain the functions. A voltage higher than 15V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 3V. The analogue multiplexer could operate on 20μA current. Using only a single voltage supply, this analog switch requires 3V~15V voltage. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. There are 70MHz bandwidths for data transfer. From the Automotive, AEC-Q100 series.
HEF4052BTT-Q100,11 Features
8 Channels
Switch Circuit: SP4T
20μA Supply Current
Bandwidth: 70MHz
HEF4052BTT-Q100,11 Applications
There are a lot of Nexperia USA Inc. HEF4052BTT-Q100,11 Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Avionics test equipment
- Fiber to the Home
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Multiplexers
- DVD-R
- SDH
- Isolation
- Communications systems
- Video signal routing
