HEF4052BTT,118
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 155Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 4052 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Power Dissipation | 500mW |
| Propagation Delay | 5 ns |
| Turn On Delay Time | 260 ns |
| Bandwidth | 70MHz |
| Turn-Off Delay Time | 205 ns |
| On-State Resistance (Max) | 155Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF |
| On-state Resistance Match-Nom | 25Ohm |
| Switch Circuit | SP4T |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1MHz |
| Switch-off Time-Max | 190ns |
| Voltage - Supply, Single (V+) | 3V~15V |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
HEF4052BTT,118 Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. Around -40°C~125°C TA is the extended operating temperature. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 8 channels. With a 5V voltage supply, the electrical component should be turned on and run. There is an electrical component included in the 16 series. SP4T switching circuits are used in these analog switch ics. 2 circuits are used in this analogue multiplexer. Search with 4052 if you are looking for analog multiplexer variants. This digital multiplexer has 155Ohm internal resistance. The functions of 16 pins can be found in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 15V. 3V is the lowest voltage that should be fed to the electronic electronic part. A voltage of 3V~15V is required to drain this analog switch from a single voltage supply. The transfer of data can be performed over 70MHz bandwidths.
HEF4052BTT,118 Features
8 Channels
Switch Circuit: SP4T
Bandwidth: 70MHz
HEF4052BTT,118 Applications
There are a lot of Nexperia USA Inc. HEF4052BTT,118 Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Cell phones
- Low-Voltage
- Medical
- Medical systems
- Cellular phones
- Sample-and-hold systems
- E1 Network Equipment
- High-Voltage
- Industrial control systems
