HEF4067BT,653
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Resistance | 115Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 4067 |
| Pin Count | 24 |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 80μA |
| Propagation Delay | 50 ns |
| Turn On Delay Time | 340 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 16 |
| Supply Type | Dual |
| Bandwidth | 70MHz |
| Turn-Off Delay Time | 435 ns |
| On-State Resistance (Max) | 155Ohm |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -50dB @ 1MHz |
| Voltage - Supply, Single (V+) | 3V~15V |
| Drain to Source Resistance | 175Ohm |
| Height Seated (Max) | 2.65mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
HEF4067BT,653 Overview
Due to its 24-SOIC (0.295, 7.50mm Width) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). This analog switch is mounted in Surface Mount. There is 16:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 24. The electronic part provides high-quality output because it has 16 channels. An 15V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 24 pins. 1 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with 4067. An switch multiplexer with 115Ohm internal resistance has a value of 115Ohm. To find out what the functions of 24 pins are, please refer to their datasheets. It is generally not recommended to supply a voltage higher than 15V to the switch device in normal circumstances. The digital multiplexer has a low cost Dual supply. A low voltage of 3V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 80μA current. Draining from a single voltage supply, this analog switch requires a voltage of 3V~15V. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. The electrical component supports 16 inputs. There are 70MHz bandwidths for data transfer. Drain to Source resistance is 175Ohm.
HEF4067BT,653 Features
16 Channels
80μA Supply Current
Bandwidth: 70MHz
Drain-to-Source resistance: 175Ohm
HEF4067BT,653 Applications
There are a lot of Nexperia USA Inc. HEF4067BT,653 Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Remote Powered Equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fiber In The Loop (FITL)
- Multi-Line E1 Interface Cards
- Signal routing between systems
- Precision data acquisition
- Battery-powered systems
- Medical systems
- Communication systems
