HI-8197PCIF
| Parameters | |
|---|---|
| Width | 5mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 31Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.8mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 16 |
| JESD-30 Code | S-PQCC-N16 |
| Supply Voltage-Min (Vsup) | 2.5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| On-State Resistance (Max) | 31Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 5nA Max |
| Channel Capacitance (CS(off), CD(off)) | 12pF 46pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 35ns, 20ns |
| Charge Injection | -10pC |
| Switch-on Time-Max | 75ns |
| Voltage - Supply, Dual (V±) | ±3V~10V |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
HI-8197PCIF Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-WQFN Exposed Pad, CSP. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 3.3V volts, the electrical part can be powered up and run. There is an electrical component included in the 16 series. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Circuits number 4 make up this analogue multiplexer. Analog switches have 31Ohm internal resistance. For the switch device to function, a voltage of 2.5V is required.
HI-8197PCIF Features
1 Channels
Switch Circuit: SPST - NO/NC
HI-8197PCIF Applications
There are a lot of Holt Integrated Circuits Inc. HI-8197PCIF Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- USB 1.1 signal switching circuits
- Fiber In The Loop (FITL)
- Isolation
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Public switching systems
- Communications systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- PCMCIA cards
- PBX interfaces
