HI6-0201HS-5
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | HI6-0201 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 12V |
| Nominal Supply Current | 3.8mA |
| Max Supply Current | 6.5mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Voltage - Supply, Single/Dual (±) | 12V~20V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 50ns, 50ns |
| Charge Injection | 10pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
HI6-0201HS-5 Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around 0°C~70°C TA are extended for operation. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. A 15V voltage supply should turn on and run the electronic component. As part of the design of the 16 series, this electronic part has been incorporated into the system. A SPST - NC switching circuit is used for these analog switches. Circuits number 4 make up this analogue multiplexer. Try searching for the analog switch ic with HI6-0201 if you are looking for variants. In this multiplexer, the internal resistance is 80Ohm. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 20V. Analog switch ics with Dual, Single supply type are cost-effective. 12V should be the lowest voltage fed to the electronic component. Putting voltage greater than 6.5mA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. If you are using dual power supplies, you should attach at least 5V. This analog switch ic utilizes SEPARATE OUTPUT output. There is a voltage range of 18V operating voltages for the electrical part.
HI6-0201HS-5 Features
1 Channels
Switch Circuit: SPST - NC
HI6-0201HS-5 Applications
There are a lot of Maxim Integrated HI6-0201HS-5 Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Audio and video routing
- Access Concentrators
- SONET
- T1/E1 Terminals
- Data Acquisition Systems
- New designs requiring multiplexer functions
- Automatic test equipment
- Public switching systems
- Power routing
