HI9P0201-9Z
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Packaging | Bulk |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 500μA |
| Max Supply Current | 2mA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 185 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 220 ns |
| Max Dual Supply Voltage | 22V |
| Off-state Isolation-Nom | 80 dB |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 55Ohm |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
HI9P0201-9Z Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOIC. To ensure high reliability, a new packaging method Bulk is used. In total, there are 16 terminations. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 16 pins. It has an internal resistance of 80Ohm. The datasheets for the 16 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 44V. Analog switch ics with Dual, Single supply type are cost-effective. An operating current of 500μA would be sufficient for this switch device. The analogue multiplexer may be damaged if voltage is greater than 2mA. Despite this switch's dual supply capability, its voltage should not exceed 22V. Temperatures above 85°C degrees Celsius should not be operated by the multiplexer. There is 55Ohm resistance between the Drain and Source on this part. 4-bits are supported.
HI9P0201-9Z Features
1 Channels
500μA Supply Current
Drain-to-Source resistance: 55Ohm
4-Bit
HI9P0201-9Z Applications
There are a lot of Intersil (Renesas Electronics America) HI9P0201-9Z Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- Access Concentrators
- PDAs
- 65 V DACs
- Transmit
- DVD-R
- Automotive applications
- Wireless Local Loop
- DSUs
- Audio and video signal routing
