HI9P0303-9Z
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 14 |
| Packaging | Bulk |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 28V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 34V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 90nA |
| Nominal Supply Current | 90μA |
| Max Supply Current | 500μA |
| Number of Bits | 2 |
| Throw Configuration | SPDT |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 18V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
HI9P0303-9Z Overview
Presented in SOIC, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Bulk is used. In total, 14 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. It is injected into the electrical part body with 14 pins. Internally, this switch multiplexer has a resistance of 50Ohm. For functions related to 14 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 34V voltage to the switch device. Dual, Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 5V. For this multiplexer to operate, 90nA current would be sufficient. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. With dual power supplies, you should attach at least 5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. This electrical part is compatible with 28V operating voltages. Temperatures over 85°C should not be allowed for the multiplexer to operate. There is 35Ohm resistance between the Drain and Source on this part. It is able to conduct in a 2-bit way.
HI9P0303-9Z Features
1 Channels
90nA Supply Current
Drain-to-Source resistance: 35Ohm
2-Bit
HI9P0303-9Z Applications
There are a lot of Intersil (Renesas Electronics America) HI9P0303-9Z Analog Switches & Multiplexers ICs applications.
- Data switching
- Digital cross connects (DSX-1)
- Audio signal routing
- DVD-R
- Imaging
- SONET
- E1 Network Equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Power routing
- Fiber to the Home
