HV9123P-G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -55°C~125°C TJ |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Technology | CMOS |
| Terminal Position | DUAL |
| Supply Voltage | 10V |
| Terminal Pitch | 2.54mm |
| Base Part Number | HV9123 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 13.5V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 13.5V |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 750μA |
| Output Configuration | Positive |
| Voltage - Supply (Vcc/Vdd) | 10V~450V |
| Control Features | Enable, Frequency Control, Reset |
| Input Voltage (Min) | 9V |
| Topology | Flyback |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 3MHz |
| Input Voltage (Max) | 80V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 30ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 20 ns |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 99 % |
| Duty Cycle (Max) | 97% |
| Height Seated (Max) | 5.334mm |
| Length | 20.066mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
HV9123P-G Overview
With its 16-DIP (0.300, 7.62mm) package, the switching controller fits the needs of most applications. It is sufficient to generate 1 outputs with this dc motor controller. There is a Tube solid enclosure around the pmic. Transistor Driver dc switching's outputs (s) are supported. The supply and operating voltage of the dc control are 10V~450V. Suitable for work in a -55°C~125°C TJ dc switcher. With this switching controller, you can switch at 3MHz. It is suitable for general dc dc regulator when it is set to Through Hole. Enable, Frequency Control, Reset is used for efficient switching control in the dcdc regulator. The switch converters are connected to a SWITCHING CONTROLLER analog IC. Terminal (s) of the switching converters are designed at the DUAL position. Different dc switching's functions can be applied to 16 terminations. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. DC switcher's input voltageis 48V volts. Other relevant dc to dc converter ics can be found by searching "HV9123". Switching converter has a total of 16 pins. This dc dc voltage regulator should be powered by a voltage of 9V. A 13.5V voltage of DC regulator was detected in the test statistics. Voltages 80V are the maximum that the dc to dc regulator will accept. It is set to 99 % duty cycle to ensure voltage regulator dc to dc reliability during power-ups and power-downs. Because of DC switcher's Through Hole, it is suitable for most prototype designs and applications. In order to run the voltage regulator dc to dc safely and reliably, users are advised to apply 13.5V. Voltage 10V must be supplied. It runs on a 750μA supply current.
HV9123P-G Features
Transistor Driver Outputs
Switching Frequency: 3MHz
Enable, Frequency Control, Reset
PULSE WIDTH MODULATION
Max Duty Cycle: 99 %
HV9123P-G Applications
There are a lot of Microchip Technology HV9123P-G DC to DC converter applications.
- Pipe bending machines
- Smart grid
- Smoke prevention equipment
- Computed tomography (CT)
- Current source circuits
- Grinders
- Serial communication converter
- Medical equipment
- Program control systems
- Elevator lighting
