ICL7611BCPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ICL7611 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 15μA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±1V~8V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 44 kHz |
| Voltage Gain | 104dB |
| Average Bias Current-Max (IIB) | 0.004μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | YES |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ICL7611BCPA+ Overview
Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tube case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. Through Hole is the recommended mounting type for this linear amplifier. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of 0°C~70°C. You can run this op amp ic on 1mA . You should keep the voltage gain at 104dB for the time being. As far as the device is concerned, buffer amplifier has 1 channels. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The operating supply voltage of the buffer op amp is rated at 8V.
ICL7611BCPA+ Features
8 Pins
supply voltage of 5V
104dB voltage gain
Output Type: Rail-to-Rail
ICL7611BCPA+ Applications
There are a lot of Maxim Integrated ICL7611BCPA+ Instrumentational OP Amps applications.
- Automatic control
- Active probe
- High-frequency data acquisition systems
- Medical instruments
- Computer workstations
- Portable docking station
- Fission chambers
- pH (acidity)
- Car stereo
- Tablets
