ICL7611DCBAZ-T
| Parameters | |
|---|---|
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 8 |
| Packaging | Cut Tape (CT) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 15V |
| Temperature Grade | COMMERCIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 2.5mA |
| Slew Rate | 1.6 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 96 dB |
| Current - Input Bias | 1pA |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 15mV |
| Bandwidth | 1.4MHz |
| Gain Bandwidth Product | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 104dB |
| Average Bias Current-Max (IIB) | 0.0004μA |
| Power Supply Rejection Ratio (PSRR) | 94dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 8V |
| Low-Bias | YES |
| Min Dual Supply Voltage | 1V |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | YES |
| Length | 4.9mm |
| Radiation Hardening | No |
ICL7611DCBAZ-T Overview
The linear amplifier is packaged in a SOIC case. The instrumentation amplifier in this picture is of the OPERATIONAL AMPLIFIER-type. Upon delivery, op amp ic is packaged in a Cut Tape (CT) case. The number of terminations is approaching the 8 mark. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 8 pins. Regarding input offset voltage, op amp rates 15mV. Using an 1mA supply current, this operational amplifier ics can be operated. Maintain 104dB as the voltage gain. There are a total of 1 channels available on the op amps. In order for op amp to function properly, the temperature should not be lower than 0°C degrees Celsius. You should only use op amp buffer at temperatures that are no higher than 70°C. The operating supply voltage of the buffer op amp is rated at 15V. As a result of this, the buffer amplifier is packed in TAPE AND REEL. In terms of the supply voltage, this electrical part is capable of operating at low voltage levels of under 16V. Keeping the linear amplifier's supply voltage above 2V is recommended. You should conduct this electronic component under the dual supply voltage of 8V.
ICL7611DCBAZ-T Features
supply voltage of 5V
104dB voltage gain
ICL7611DCBAZ-T Applications
There are a lot of Intersil (Renesas Electronics America) ICL7611DCBAZ-T Instrumentational OP Amps applications.
- Micro signal measurement
- Power transmission
- Large motor controllers
- Television
- Computer workstations
- Broadcasting
- Differentiator circuits
- Switching amplifier
- Measurements of Wheatstone bridge
- High/low-pass filter circuit
