ICL7611DCSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ICL7611 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Number of Circuits | 1 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 15μA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±1V~8V |
| Input Offset Voltage (Vos) | 15mV |
| Gain Bandwidth Product | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 44 kHz |
| Voltage Gain | 104dB |
| Average Bias Current-Max (IIB) | 0.004μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | YES |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ICL7611DCSA+ Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. A General Purpose-type buffer amplifier is shown here. A Tube case is used to deliver the buffer op amp. There is a growing number of terminations approaching the number of 8. A total of 8 pins are attached to buffer op amp. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. Op amp rates 15mV as input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureAs long as the supply current of the chip does not exceed 1mA, this op amp ic can operate. 104dB should be the voltage gain. A linear amplifier like this has 1 circuits on it. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of instrumentation amplifier is rated 8V voltage.
ICL7611DCSA+ Features
8 Pins
supply voltage of 5V
104dB voltage gain
Output Type: Rail-to-Rail
ICL7611DCSA+ Applications
There are a lot of Maxim Integrated ICL7611DCSA+ Instrumentational OP Amps applications.
- Communication
- Strain gauges
- Addition operation circuits
- Inverse/same-phase proportional circuit
- single/dual op amp sum and difference circuits
- Subtraction operation circuits
- Active probe
- Multiplication circuits
- Navigation
- Switching amplifier
