ICL7612ACPA
| Parameters | |
|---|---|
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 1mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±1V~8V |
| Gain Bandwidth Product | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 44 kHz |
| Average Bias Current-Max (IIB) | 0.004μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Voltage - Input Offset | 2mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | YES |
| Neg Supply Voltage-Max (Vsup) | -9V |
| Voltage Gain-Min | 6300 |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ICL7612 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
ICL7612ACPA Overview
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. Buffer amps of this type are called General Purpose-types. The op amp is delivered to you in a Tube case. During the past two weeks, there have been close to 8 terminations. Buffer amplifier has a total of 8 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. For this electrical component, Through Hole is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . This op amp ic has 1 circuits. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. It is recommended that this electronic component be used with an 1mA supply. To conduct electronic part voltage gain higher than 6300.
ICL7612ACPA Features
8 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
ICL7612ACPA Applications
There are a lot of Maxim Integrated ICL7612ACPA Instrumentational OP Amps applications.
- Multimedia playback equipment
- Fission chambers
- Scintillation detectors
- Precision measurement
- Weak signal detection
- High/low-pass filter circuit
- Computer workstations
- Biopotential
- Radar
- RF cable systems
