Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Package / Case |
SOIC |
Packaging |
Tape & Reel |
Published |
2005 |
JESD-609 Code |
e3 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Max Operating Temperature |
70°C |
Min Operating Temperature |
0°C |
Subcategory |
Operational Amplifier |
Packing Method |
TAPE AND REEL |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Pin Count |
8, 8 |
JESD-30 Code |
R-PDSO-G8 |
Operating Supply Voltage |
15V |
Temperature Grade |
COMMERCIAL |
Number of Channels |
1 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2V |
Operating Supply Current |
1mA |
Nominal Supply Current |
2.5mA |
Slew Rate |
1.6 V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
OPERATIONAL AMPLIFIER |
Common Mode Rejection Ratio |
96 dB |
Current - Input Bias |
1pA |
Output Current per Channel |
40mA |
Input Offset Voltage (Vos) |
15mV |
Bandwidth |
1.4MHz |
Gain Bandwidth Product |
1.4MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Unity Gain BW-Nom |
1400 kHz |
Voltage Gain |
104dB |
Average Bias Current-Max (IIB) |
0.0004μA |
Power Supply Rejection Ratio (PSRR) |
94dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Max Dual Supply Voltage |
8V |
Low-Bias |
YES |
Min Dual Supply Voltage |
1V |
Bias Current-Max (IIB) @25C |
0.00005μA |
Programmable Power |
YES |
Length |
4.9mm |
Radiation Hardening |
No |
RoHS Status |
RoHS Compliant |
Lead Free |
Lead Free |
ICL7612DCBAZ-T Overview
It is packaged in an SOIC-case that protects the operational amplifiers from damage. An op amp of this type is a OPERATIONAL AMPLIFIER-type. There is a Tape & Reel case that is delivered with the instrumentation amplifiers. It is estimated that there will be at least 8 terminations this year. Buffer amplifier has a total of 8, 8 pins on it. Please take in mind that op amp should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In terms of the input offset voltage, instrumentation amplifier rates at 15mV. The buffer amplifier is capable of operating from a supply current of 1mA . Maintain 104dB as the voltage gain. The op amp ic has 1 channels on it. In order for op amp to function properly, the temperature should not be lower than 0°C degrees Celsius. It is recommended that op amp be used at temperatures below 70°C. The operating supply voltage of instrumentation amplifier is rated 15V voltage. As a result of this, the buffer amplifier is packed in TAPE AND REEL. Regarding the voltage of the supply, this electrical part can work from a voltage as low as 16V, and this is an excellent feature. To keep the buffer amps' supply voltage higher than 2V. This electrical part should be conducted under the dual supply voltage of 8V volts when you conduct this part.
ICL7612DCBAZ-T Features
8, 8 Pins
supply voltage of 5V
104dB voltage gain
ICL7612DCBAZ-T Applications
There are a lot of Intersil (Renesas Electronics America) ICL7612DCBAZ-T Instrumentational OP Amps applications.
- Mobile phone
- High input resistance broadband
- earphone
- Automation control systems
- Signal amplification
- Displayers for aircraft and air transportation control systems
- Television broadcasting equipment
- Band-pass filter
- Vehicle electronics
- Ultrasound transducers