ICL7621BCPA+
| Parameters | |
|---|---|
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ICL7621 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Power Supplies | +-1/+-5V |
| Number of Circuits | 2 |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 15μA |
| Slew Rate | 0.016V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±1V~8V |
| Input Offset Voltage (Vos) | 5mV |
| Gain Bandwidth Product | 480kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 44 kHz |
| Voltage Gain | 104dB |
| Average Bias Current-Max (IIB) | 0.004μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Length | 9.375mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
ICL7621BCPA+ Overview
It is packaged in an 8-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. A General Purpose-type buffer amplifier is shown here. A Tube case is used to deliver the buffer op amp. The number of terminations is approaching the 8 mark. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. In total, the buffer amplifier consists of 8 pins. In terms of input offset voltage, operational amplifier rates 5mV. This electrical part should be mounted using type Through Hole. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. An 100μA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 104dB. On this buffer amplifier, there are 2 circuits. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 8V.
ICL7621BCPA+ Features
8 Pins
supply voltage of 5V
104dB voltage gain
Output Type: Rail-to-Rail
ICL7621BCPA+ Applications
There are a lot of Maxim Integrated ICL7621BCPA+ Instrumentational OP Amps applications.
- MP3
- Tablets
- Cinema or auditorium audio system
- Fast A/D and D/A converters
- Power control
- E-book readers
- Logarithmic operation circuits
- High input resistance broadband
- Polarized electrodes
- Home audio systems
