ICL7652P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | ICL7652 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Number of Elements | 2 |
| Number of Channels | 1 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 2.4mA |
| Power Dissipation | 1W |
| Slew Rate | 3.1V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 4pA |
| Voltage - Supply, Single/Dual (±) | 3.8V~16V ±1.9V~8V |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 1.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1900 kHz |
| Voltage Gain | 150dB |
| Average Bias Current-Max (IIB) | 0.00003μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 8V |
| Voltage - Input Offset | 600μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00003μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Max I/O Voltage | 5μV |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ICL7652P Overview
Op amp is packaged in 8-DIP (0.300, 7.62mm) case. There are two types of operational amplifiers in this circuit. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be at least 8 terminations this year. The pins on this board total to 8 in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are available on the instrumentation amplifier. With regard to input offset voltage, instrumentation amplifier is rated at 5μV. Through Hole is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. Using a supply current of 1.5mA , this buffer op amp will be able to operate. Voltage gain should remain at 150dB. On the buffer amps, there are 1 channels that can be used. The total number of elements in this buffer amplifier is 2. The operating supply voltage of the buffer op amp is rated at 8V. As the name implies, LinCMOS? refers to the series of the buffer op amp.
ICL7652P Features
8 Pins
supply voltage of 5V
150dB voltage gain
ICL7652P Applications
There are a lot of Texas Instruments ICL7652P Instrumentational OP Amps applications.
- Polarized electrodes
- Portable electronic products powered by batteries
- Integrator circuits
- Band-stop filter
- Blood pressure sensors
- High/low-pass filter circuit
- E-book readers
- Professional videography
- Signal amplification
- Industrial applications including automation
