IDT74FCT823ATSOG8
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 24 |
| Packaging | Tape and Reel |
| Published | 2006 |
| JESD-609 Code | e3 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 24 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 24 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 9 |
| Propagation Delay | 23 ns |
| Turn On Delay Time | 1.5 ns |
| Family | FCT |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.048 A |
| High Level Output Current | 48mA |
| Low Level Output Current | 15mA |
| Clock Edge Trigger Type | Positive Edge |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
IDT74FCT823ATSOG8 Overview
As a result, it is packaged as SOIC. The Tape and Reelpackage contains it. A total of 1 elements are present. Currently, there are 24 terminations. An input voltage of 5Vpowers the D latch. In this case, the D flip flop belongs to the FCTfamily. This electronic part is mounted in the way of Surface Mount. A total of 24pins are provided on this board. It has a clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. 9bits are used in its design. It operates from 5V power supplies. The flip flop has 2embedded ports. For high efficiency, the supply voltage should be kept at 5V. It is also characterized by WITH CLEAR AND CLOCK ENABLE. 48mAis the output current at high level. In the low level output current setting, 15mAis used. It is recommended that the operating temperature be lower than 85°C. Temperatures above -40°Cshould be used. The RS flip flop is designed to operate with a minimal supply voltage of 4.75VV. It supports a maximum supply voltage of 5.25V volts. This logic IC is BUS DRIVER. A total of 1 functions are provided by this T flip flop. 24pins are available on this JK flip flop.
IDT74FCT823ATSOG8 Features
Tape and Reel package
24 pins
9 Bits
5V power supplies
1 Functions
24 pin count
IDT74FCT823ATSOG8 Applications
There are a lot of Integrated Device Technology (IDT) IDT74FCT823ATSOG8 Flip Flops applications.
- Count Modes
- Patented noise
- Differential Individual
- Buffered Clock
- Common Clocks
- Communications
- 2 – Bit synchronous counter
- Computers
- Shift Registers
- Latch-up performance
