banner_page

IDT74FST163245PAG

48 Terminations48 Pin Signal switch2 FunctionsMin 4.5V VMax 5.5V V


  • Manufacturer: Integrated Device Technology (IDT)
  • Nocochips NO: 378-IDT74FST163245PAG
  • Package: TSSOP
  • Datasheet: PDF
  • Stock: 647
  • Description: 48 Terminations48 Pin Signal switch2 FunctionsMin 4.5V VMax 5.5V V(Kg)

Details

Tags

Parameters
Mount Surface Mount
Package / Case TSSOP
Number of Pins 48
Packaging Rail/Tube
Published 2006
JESD-609 Code e3
Moisture Sensitivity Level (MSL) 1
Number of Terminations 48
Terminal Finish Matte Tin (Sn) - annealed
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Subcategory Bus Driver/Transceivers
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 5V
Terminal Pitch 0.5mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 30
Pin Count 48
Qualification Status Not Qualified
Operating Supply Voltage 5V
Power Supplies 5V
Temperature Grade INDUSTRIAL
Max Supply Voltage 5.5V
Min Supply Voltage 4.5V
Number of Ports 2
Number of Bits 16
Propagation Delay 6.5 ns
Quiescent Current 3μA
Family CBT/FST/QS/5C/B
Output Characteristics 3-STATE
Supply Type Single
Output Polarity TRUE
Logic IC Type BUS DRIVER
High Level Output Current -128mA
Low Level Output Current 128mA
Independent Circuits 2
Width 6.1mm
RoHS Status RoHS Compliant

IDT74FST163245PAG Overview


The reason it is provided is that the board space can be saved by placing digital switch in the TSSOP.The package is packaged in the manner of Rail/Tube.There is a design for terminating 48 as part of its basic configuration.For multiplexer's system, a voltage of 5V is supplied.A component pin count of 48 can be found on this turn signal switch.Using the point GULL WING as an end point of conductors, it is used to determine the terminus of a conductor.In this case, the supply type is Single.The board is configured with 48 pins.The mounting is in the way of Surface Mount.The CBT/FST/QS/5C/B family includes the logic switch.In this signal multiplexer, there are 16 bits provided.Normally, 5V is powered by a battery.The digital switch ic is a part of an electronic system classified as Bus Driver/Transceivers.Without external influences, it consumes 3μA current of multiplexer ic.When a supply voltage of 5V is used, reliable performance of the multiplexers can be achieved.A resistance of 2 governs its operation.At 85°C, the maximum operating temperature of this signal switch is acceptable.It is recommended that the minimal operating temperature of the multiplexer be maintained at -40°C.The relevant device specification specifies a maximum supply voltage of 5.5V for the signal switches.Device specifications require that the digital swith operate at a minimum supply voltage of 4.5V.As its logic IC, it uses BUS DRIVER.

IDT74FST163245PAG Features


Supplied in the TSSOP package
Adopting a supply type of Single
Power supplies of 5V
Operating with the supply voltage of 5V
BUS DRIVER as the logic IC

IDT74FST163245PAG Applications


There are a lot of Integrated Device Technology (IDT) IDT74FST163245PAG Signal Switches / Multiplexers / Decoders applications.

  • Electronics industry
  • Analog, digital or video signal switching
  • Make half adder
  • Automation system
  • Enabling block of memory depending on address in memory chips
  • Code conversion
  • Encrypted communications system
  • Idle motor
  • Microprocessor input/output systems
  • Microprocessor memory systems

Write a review

Note: HTML is not translated!
    Bad           Good