IDT74LVC273APGG8
| Parameters | |
|---|---|
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.7V |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Propagation Delay | 9.5 ns |
| Turn On Delay Time | 1.5 ns |
| Family | LVC/LCX/Z |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.024 A |
| High Level Output Current | 24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Packaging | Digi-Reel® |
| Published | 2006 |
| JESD-609 Code | e3 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
IDT74LVC273APGG8 Overview
The item is packaged in TSSOPcases. You can find it in the Digi-Reel?package. There are 1 elements in it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Power is provided by a 3.3V supply. Electronic devices of this type belong to the LVC/LCX/Zfamily. A part of the electronic system is mounted in the way of Surface Mount. This board is designed with 20pins on it. The clock edge trigger type for this device is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. There are 8bits in its design. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. High efficiency requires the supply voltage to be maintained at 3.3V. There is 24mA output current at the high level. A 24mAvalue is set for low-level output current. The operating temperature should be lower than 85°C. In order for the system to operate properly, the temperature should be higher than -40°C. A minimum supply voltage of 2.7V is required for these RS flip flops to operate. The maximum supply voltage supported by the flip flop is 3.6V. It uses the logic IC D FLIP-FLOP. Currently, it is equipped with 1 functions . The D latch is equipped with 20 pins.
IDT74LVC273APGG8 Features
Digi-Reel? package
20 pins
8 Bits
1 Functions
20 pin count
IDT74LVC273APGG8 Applications
There are a lot of Integrated Device Technology (IDT) IDT74LVC273APGG8 Flip Flops applications.
- Power down protection
- Instrumentation
- Safety Clamp
- Storage registers
- Digital electronics systems
- 2 – Bit synchronous counter
- EMI reduction circuitry
- Supports Live Insertion
- Computers
- Matched Rise and Fall
