IH5040CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | IH5040 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 400 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 400ns, 200ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
IH5040CPE Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. In Through Hole, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. The total number of terminations is 16. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component like this is included in the 16 series. These analog multiplexers are built based on SPST - NO switching circuits. It consists of 1 circuits. If you are looking for variants of the digital switch, trying search with IH5040. This digital multiplexer has 80Ohm internal resistance. The functions of 16 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. A analog switch ic that has a cost-effective Dual supply type. 4.5V is the lowest voltage that should be fed to the electronic electronic part. The switch multiplexer may be damaged if it is exposed to voltage greater than 10μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. In the case of dual power supplies, you should connect at least 4.5V.
IH5040CPE Features
1 Channels
Switch Circuit: SPST - NO
IH5040CPE Applications
There are a lot of Maxim Integrated IH5040CPE Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- DVD-R
- FTTH
- Fiber to the Home
- Avionics and Military Systems
- Channelized and Unchannelized DS3 applications
- Cable PC
- Battery Powered Instruments
- Communications systems
- Fault Tolerant Systems
