banner_page

IH5041CPE

400ns, 200ns SPST - NO 80Ohm Analog Switches BREAK-BEFORE-MAKE IH5041 16 Pins 5nA 15V 16-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-IH5041CPE
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: -
  • Stock: 392
  • Description: 400ns, 200ns SPST - NO 80Ohm Analog Switches BREAK-BEFORE-MAKE IH5041 16 Pins 5nA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Terminal Finish Tin/Lead (Sn85Pb15)
Subcategory Multiplexer or Switches
Max Power Dissipation 842mW
Technology CMOS
Peak Reflow Temperature (Cel) 240
Number of Functions 2
Supply Voltage 15V
Time@Peak Reflow Temperature-Max (s) 20
Base Part Number IH5041
Output SEPARATE OUTPUT
Pin Count 16
Power Supplies 5+-15V
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 18V
Min Supply Voltage 4.5V
Max Supply Current 10μA
Throw Configuration SPST
Turn On Delay Time 400 ns
Supply Type Dual
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 200 ns
Max Dual Supply Voltage 18V
On-State Resistance (Max) 80Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 50 dB
Current - Leakage (IS(off)) (Max) 5nA
On-state Resistance Match-Nom 5Ohm
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 400ns, 200ns
Channel-to-Channel Matching (ΔRon) 5 Ω
Switching BREAK-BEFORE-MAKE
Normal Position NO
Voltage - Supply, Dual (V±) ±4.5V~18V
Length 19.175mm
Radiation Hardening No
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead
Mount Through Hole
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Number of Pins 16
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 2003
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 80Ohm

IH5041CPE Overview


The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Through Hole position. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of 0°C~70°C TA degrees Celsius. A total of 16 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. 16 pins are injected to the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. There are 2 circuits in this multiplexer. IH5041 can be used to search for analog multiplexer variants. A 80Ohm internal resistance characterizes this multiplexer. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 18V. A cost-effective Dual supply type analogue multiplexer. 4.5V is the lowest voltage that should be fed to the electronic electronic part. Putting voltage greater than 10μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. When using dual power supplies, you should attach at least 4.5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.

IH5041CPE Features


1 Channels
Switch Circuit: SPST - NO

IH5041CPE Applications


There are a lot of Maxim Integrated IH5041CPE Analog Switches & Multiplexers ICs applications.

  • Fiber to the Home
  • Digital Cross-Connects
  • Remote Powered Equipment
  • PDH Multiplexers
  • SDH/SONET multiplexers
  • Automatic test equipment
  • Audio signal routing
  • Audio and video signal routing
  • Avionics
  • Digital access cross connects

Write a review

Note: HTML is not translated!
    Bad           Good