IH5042CWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | IH5042 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 10μA |
| Number of Bits | 4 |
| Turn On Delay Time | 400 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 400ns, 200ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
IH5042CWE+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.295, 7.50mm Width). Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 2:1. Extended operating temperature around 0°C~70°C TA. Total terminations are 16. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. There is an electrical component included in the 16 series. SPDT switching circuits are used in these analog switch ics. It consists of 1 circuits. IH5042 can be used to search for analog multiplexer variants. There is 80Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 18V. Digital switch that provides Dual power at a cost-effective price. It is recommended to use 4.5V as the lowest voltage for the electrical part. Putting voltage greater than 10μA on the multiplexer may cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. The voltage should be at least 4.5V if you are using dual power supplies. Its conductivity is 4-bit.
IH5042CWE+ Features
1 Channels
Switch Circuit: SPDT
4-Bit
IH5042CWE+ Applications
There are a lot of Maxim Integrated IH5042CWE+ Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Multi-Line E1 Interface Cards
- Channel Banks
- Power routing
- Avionics test equipment
- 65 V DACs
- Automotive applications
- Voice over IP/DSL – Integrated Access Devices, Smart
- E1 Network Equipment
- FTTH
