IH5045CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | DPST - NC |
| Switch Time (Ton, Toff) (Max) | 400ns, 200ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
IH5045CPE+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). 2:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. Total terminations are 16. Due to its 2 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electronic part body is injected with 16 pins. On the other hand, analog switches can be constructed using DPST - NC switching circuits. There are 2 circuits in this switch device. As far as internal resistance is concerned, it has 80Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 18V. In the case of dual power supplies, you should connect at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic.
IH5045CPE+ Features
2 Channels
Switch Circuit: DPST - NC
IH5045CPE+ Applications
There are a lot of Maxim Integrated IH5045CPE+ Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- Communication systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- T1/E1 Terminals
- Fiber to the Home
- Routers
- Fiber In The Loop (FITL)
- Precision data acquisition
- PCMCIA cards
