IH5049CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | IH5049 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | DPST |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 75Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| On-state Resistance Match-Nom | 8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 600ns, 300ns (Typ) |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 8 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~20V |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
IH5049CPE+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, there are 16 terminations. The electronic part delivers high-quality output through its 2 channels. With a 15V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 16 series. Unlike digital switches, these are based on SPST - NO switching circuits. Circuits number 2 make up this analogue multiplexer. IH5049 can be used to search for analog multiplexer variants. There is 45Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 20V should not normally be supplied to the switches. The analog switch ic is of the Dual supply type and is cost-effective. A low voltage of 4.5V should be applied to the electronic component. This multiplexer would work with 10μA current. A digital multiplexer may suffer damage if voltage is applied above 10μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. This product is integrated with an analog integrated circuit (IC) of type DPST. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
IH5049CPE+ Features
2 Channels
Switch Circuit: SPST - NO
10μA Supply Current
IH5049CPE+ Applications
There are a lot of Maxim Integrated IH5049CPE+ Analog Switches & Multiplexers ICs applications.
- Transmit
- DVD-R
- Battery-powered systems
- Fiber In The Loop (FITL)
- Remote Powered Equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- Communication systems
- Audio and video routing
- Digital access cross connects
- FTTH
