IH5050CPE
| Parameters | |
|---|---|
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | IH5050 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 33V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 100μA |
| Turn On Delay Time | 600 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 75Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| On-state Resistance Match-Nom | 8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 600ns, 300ns (Typ) |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 8 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±4.5V~20V |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Through Hole |
| Mounting Type | Through Hole |
IH5050CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Increasing operating temperature to around 0°C~70°C TA. The total number of terminations is 16. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. It is injected into the electrical part body with 16 pins. Unlike digital switches, these are based on SPDT switching circuits. It consists of 1 circuits. IH5050 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 45Ohm. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 33V. Analogue multiplexers of the Dual supply type that are cost-effective. It is recommended to use 5V as the lowest voltage for the electrical part. The switch device would be able to operate with 10μA current. Put voltage above 100μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V.
IH5050CPE Features
1 Channels
Switch Circuit: SPDT
10μA Supply Current
IH5050CPE Applications
There are a lot of Maxim Integrated IH5050CPE Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Channel Banks
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Industrial control systems
- Remote Powered Equipment
- Battery Powered Systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Medical systems
- Medical
- ISDN NT1/TA
