IH5141CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | IH5141 |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 125 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 125ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
IH5141CPE Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around 0°C~70°C TA. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. This electronic part can be found in the 16 series. SPST - NO switching circuits are used in these analog switch ics. It consists of 2 circuits. Search with IH5141 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 100Ohm. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. Analogue multiplexer with a Dual supply type that is cost-effective. It is recommended to use 4.5V as the lowest voltage for the electrical part. The analogue multiplexer may be damaged if voltage is greater than 10μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. In the case of dual power supplies, you should connect at least 4.5V.
IH5141CPE Features
1 Channels
Switch Circuit: SPST - NO
IH5141CPE Applications
There are a lot of Maxim Integrated IH5141CPE Analog Switches & Multiplexers ICs applications.
- Video switching
- Audio and video switching
- Remote Powered Equipment
- Sample hold systems
- Fault Tolerant Systems
- Signal routing between systems
- E1 Network Equipment
- Relay replacements
- Multi-Line E1 Interface Cards
- Voice over IP/DSL – Integrated Access Devices, Smart
