IH5143CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | IH5143 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5+-15V |
| Number of Channels | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 10μA |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Length | 19.175mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
IH5143CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. This analog switch is mounted in Through Hole. 2:1 is the ratio between multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 16. Due to its 2 channels, the electrical component produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. 16 pins are injected to the electronic part body. These analog multiplexers are built based on SPDT switching circuits. Try searching for the analog switch ic with IH5143 if you are looking for variants. This digital multiplexer has 100Ohm internal resistance. The functions of 16 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. The digital multiplexer has a low cost Dual supply. The lowest voltage fed to the electronic component should be 4.5V. Put voltage above 10μA on the multiplexer to cause damage. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 4.5V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
IH5143CPE Features
2 Channels
Switch Circuit: SPDT
IH5143CPE Applications
There are a lot of Maxim Integrated IH5143CPE Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Routers
- Precision data acquisition
- MP3 players
- Multi-Line E1 Interface Cards
- Industrial and process control systems
- Medical
- Signal routing between systems
- Access Concentrators
- Battery Powered Systems
