IH5143CWE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | IH5143 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 150ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
IH5143CWE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.295, 7.50mm Width). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around 0°C~70°C TA. Totally, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electrical component body receives 16 pins. Based on SPDT switching circuits, these analog multiplexers work. Circuits number 2 make up this analogue multiplexer. Try searching with IH5143 if you're looking for variants. A 100Ohm internal resistance characterizes this multiplexer. Theswitch device is a typical Multiplexer or Switches. The digital multiplexer has a low cost Dual supply. For this switch, a dual supply voltage is feasible, but it must not exceed 18VWhen using dual power supplies, you should attach at least 4.5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A voltage of 15V can be used to operate the electronic component.
IH5143CWE Features
1 Channels
Switch Circuit: SPDT
IH5143CWE Applications
There are a lot of Maxim Integrated IH5143CWE Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- FTTH
- Avionics test equipment
- Fiber In The Loop (FITL)
- Cell phones
- Intelligent PBX
- Frame Relay Equipment
- SONET
- SDH/SONET multiplexers
- Power routing
