INA101KU
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 420.395078mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| ECCN Code | EAR99 |
| Resistance | 10GOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 600mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | INA101 |
| Pin Count | 16 |
| Number of Circuits | 1 |
| Operating Supply Current | 6.7mA |
| Nominal Supply Current | 6.7mA |
| Power Dissipation | 600mW |
| Output Current | 10mA |
| Quiescent Current | 6.7mA |
| Slew Rate | 0.4V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | ±5V~20V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 25 kHz |
| Gain Bandwidth Product | 300 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 60dB |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 125μV |
| Gain | 1000 dB |
| -3db Bandwidth | 0.3MHz |
| Dual Supply Voltage | 15V |
| Neg Supply Voltage-Max (Vsup) | -20V |
| Number of Amplifiers | 3 |
| Voltage Gain-Nom | 10 |
| Non-linearity-Max | 0.002% |
| Height | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
INA101KU Overview
Packaging for the buffer amplifier is in the form of a 16-SOIC (0.295, 7.50mm Width) case. Buffer amps of this type are called Instrumentation-types. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. In this case, there are 16 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. It has 16 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 250μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, op amp ranges 0°C~70°C. Using a supply current of 6.7mA , this buffer op amp will be able to operate. There should be no change in the voltage gain at 60dB. This op amp ic has 1 circuits. There is an 6.7mA quiescent current running through op amp ic. It is important to keep the resistance within the 10GOhm range of the linear amplifier. The linear amplifier has 3 amplifiers.
INA101KU Features
16 Pins
supply voltage of 15V
60dB voltage gain
Resistance of 10GOhm
INA101KU Applications
There are a lot of Texas Instruments INA101KU Instrumentational OP Amps applications.
- pH (acidity)
- Radar
- Power generator
- Automation control systems
- Micro signal measurement
- Displayers for aircraft and air transportation control systems
- Fast A/D and D/A converters
- Inverse/same-phase proportional circuit
- Non-polarized electrodes
- Information processing
