banner_page

INA105KP

1 Channels 20mA per Channel 72 dB Instrumentational OP Amps ±5V~18V INA105 8 Pins 8-DIP (0.300, 7.62mm)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-INA105KP
  • Package: 8-DIP (0.300, 7.62mm)
  • Datasheet: -
  • Stock: 849
  • Description: 1 Channels 20mA per Channel 72 dB Instrumentational OP Amps ±5V~18V INA105 8 Pins 8-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 3 days ago)
Mounting Type Through Hole
Package / Case 8-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 8
Weight 528.605208mg
Operating Temperature -40°C~85°C
Packaging Tube
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Resistance 50kOhm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Operational Amplifier
Technology BIPOLAR
Number of Functions 1
Supply Voltage 15V
Terminal Pitch 2.54mm
Base Part Number INA105
Pin Count 8
Number of Channels 1
Operating Supply Current 1.5mA
Nominal Supply Current 1.5mA
Quiescent Current 1.5mA
Slew Rate 3V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type Differential
Common Mode Rejection Ratio 72 dB
Max Input Voltage 20V
Voltage - Supply, Single/Dual (±) ±5V~18V
Output Current per Channel 20mA
Supply Type Dual
Input Offset Voltage (Vos) 500μV
Bandwidth 1MHz
Gain Bandwidth Product 50 kHz
Neg Supply Voltage-Nom (Vsup) -15V
Voltage Gain 0dB
Low-Offset YES
Frequency Compensation YES
Voltage - Input Offset 50μV
Micropower NO
-3db Bandwidth 1MHz
Programmable Power NO
Dual Supply Voltage 15V
Power NO
Voltage Gain-Nom 1
Height 5.08mm
Length 9.81mm
Width 6.35mm
Thickness 3.9mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

INA105KP Overview


Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. A Differential-type buffer amplifier is shown here. The op amp is delivered to you in a Tube case. During the past two weeks, there have been close to 8 terminations. It consists of a total of 8 pins in total. This linear amplifier should be powered by an 15V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 8 pins are located on the operational amplifiers. Op amp rates 500μV as input offset voltage. It is recommended that this electronic component be mounted using the Through Hole mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. Using a supply current of 1.5mA , this buffer op amp will be able to operate. There should be no change in the voltage gain at 0dB. The op amp ic has 1 channels on it. The current is quiescent at 1.5mA. It is important to keep the resistance within the 50kOhm range of the op amps.

INA105KP Features


8 Pins
supply voltage of 15V
0dB voltage gain
Resistance of 50kOhm

INA105KP Applications


There are a lot of Texas Instruments INA105KP Instrumentational OP Amps applications.

  • Power control
  • Inverse/same-phase proportional circuit
  • Thermocouples
  • Industrial control system
  • Displayers for aircraft and air transportation control systems
  • Automotive sensors
  • Medical imaging
  • Wireless base stations
  • High speed sample
  • Weak signal detection

Write a review

Note: HTML is not translated!
    Bad           Good