INA105KPG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 528.605208mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 50kOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | INA105 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 2mA |
| Quiescent Current | 1.5mA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 72 dB |
| Voltage - Supply, Single/Dual (±) | ±5V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 0dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 50μV |
| Micropower | NO |
| -3db Bandwidth | 1MHz |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Power | NO |
| Voltage Gain-Nom | 1 |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
INA105KPG4 Overview
The linear amplifier is packaged in a 8-DIP (0.300, 7.62mm) case which makes it easy for the consumer to handle. Differential-type instrumentation amplifiers are used in this application. In the case of Tube cases, linear amplifier will be delivered. There is a growing number of terminations approaching the number of 8. There are a total of 8 pins on this op amp. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 500μV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . You can run this op amp ic on 1.5mA . The voltage gain should stay at 0dB. There are a total of 1 elements in this linear amplifier. There is a quiescent current of 1.5mA in this operational amplifier circuit. Instrumentation amplifier resistance should stay within the range of 50kOhm.
INA105KPG4 Features
8 Pins
supply voltage of 15V
0dB voltage gain
Resistance of 50kOhm
INA105KPG4 Applications
There are a lot of Texas Instruments INA105KPG4 Instrumentational OP Amps applications.
- Laptop
- earphone
- Comparator
- Video conversion and routing
- Non-polarized electrodes
- Communication
- Test and measurement instruments
- Medical instruments
- Portable media players
- Proportional counter tubes
