INA106KP
| Parameters | |
|---|---|
| -3db Bandwidth | 1MHz |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Power | NO |
| Voltage Gain-Nom | 10 |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 528.605208mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Resistance | 110kOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | INA106 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.5mA |
| Quiescent Current | 1.5mA |
| Min Input Voltage | 4V |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 86 dB |
| Max Input Voltage | -4V |
| Voltage - Supply, Single/Dual (±) | ±5V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 20dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 50μV |
| Micropower | NO |
INA106KP Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. An op amp of this type is a Differential-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations approaches 8. It consists of a total of 8 pins in total. It is important to remember that this op amp should be operated at a voltage of 15V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. The buffer op amp includes 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 200μV. Through Hole is the recommended mounting type of operational amplifiers. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. You can run this op amp ic on 1.5mA . 20dB should remain the voltage gain. The op amp ic has 1 channels on it. The current is quiescent at 1.5mA. Instrumentation amplifier resistance should stay within the range of 110kOhm.
INA106KP Features
8 Pins
supply voltage of 15V
20dB voltage gain
Resistance of 110kOhm
INA106KP Applications
There are a lot of Texas Instruments INA106KP Instrumentational OP Amps applications.
- Micro signal measurement
- Biopotential
- Vehicle electronics
- Laptop
- Gaming industry
- Comparator
- Wireless base stations
- Scintillation detectors
- pH (acidity)
- Blood pressure sensors
