INA106U
| Parameters | |
|---|---|
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 110kOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | INA106 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 2mA |
| Quiescent Current | 1.5mA |
| Min Input Voltage | 4V |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 86 dB |
| Max Input Voltage | -4V |
| Voltage - Supply, Single/Dual (±) | ±5V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 20dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 50μV |
| Micropower | NO |
| -3db Bandwidth | 1MHz |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Power | NO |
| Voltage Gain-Nom | 10 |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
INA106U Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. Differential-type instrumentation amplifiers are used in this application. In the case of Tube cases, linear amplifier will be delivered. The number of terminations is approaching the 8 mark. It consists of a total of 8 pins in total. It is important to remember that this op amp should be operated at a voltage of 15V volts. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 200μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 1.5mA and 10 . There should be no change in the voltage gain at 20dB. On the buffer amps, there are 1 channels that can be used. The quiescent current is 1.5mA. 110kOhm should be the range of resistance for the linear amplifier.
INA106U Features
8 Pins
supply voltage of 15V
20dB voltage gain
Resistance of 110kOhm
INA106U Applications
There are a lot of Texas Instruments INA106U Instrumentational OP Amps applications.
- Mobile phone
- Navigation
- Medical imaging
- Computer workstations
- Signal transformation
- Digital cameras
- Vehicle electronics
- Image computer boards
- Differentiator circuits
- Car stereo
