Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mounting Type |
Through Hole |
Package / Case |
8-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
8 |
Weight |
528.605208mg |
Operating Temperature |
-40°C~85°C |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
ECCN Code |
EAR99 |
Resistance |
10 TΩ |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Terminal Position |
DUAL |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
2.54mm |
Base Part Number |
INA111 |
Pin Count |
8 |
Number of Circuits |
1 |
Operating Supply Current |
3.3mA |
Nominal Supply Current |
4.5mA |
Max Supply Current |
4.5mA |
Quiescent Current |
3.3mA |
Slew Rate |
17V/μs |
Amplifier Type |
Instrumentation |
Common Mode Rejection Ratio |
106 dB |
Current - Input Bias |
2pA |
Voltage - Supply, Single/Dual (±) |
±6V~18V |
Output Current per Channel |
30mA |
Input Offset Voltage (Vos) |
500μV |
Bandwidth |
2MHz |
Gain Bandwidth Product |
2MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Voltage Gain |
80dB |
Average Bias Current-Max (IIB) |
0.00002μA |
Voltage - Input Offset |
100μV |
-3db Bandwidth |
2MHz |
Dual Supply Voltage |
15V |
Input Voltage Noise Density |
10nV/sqrt Hz |
Number of Amplifiers |
3 |
Voltage Gain-Nom |
10 |
Non-linearity-Max |
0.02% |
Height |
5.08mm |
Length |
9.81mm |
Width |
6.35mm |
Thickness |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
INA111BP Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. The instrumentation amplifier in this picture is of the Instrumentation-type. Linear amplifier is delivered in a Tube case. It consists of a total of 8 pins in total. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. 8 pins are included on the operational amplifiers. The input offset voltage is 500μV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. It is important to note that this linear amplifier works well at a temperature of -40°C~85°C when it comes to operating temperatureAs long as the supply current of the chip does not exceed 3.3mA, this op amp ic can operate. Voltage gain should remain at 80dB. On this instrumentation amplifier, there are 1 circuits that are connected together. The current is quiescent at 3.3mA. It is important that the op amp resistance stays within the range of 10 TΩ. There are 3 amplifiers on it.
INA111BP Features
8 Pins
supply voltage of 15V
80dB voltage gain
Resistance of 10 TΩ
INA111BP Applications
There are a lot of Texas Instruments INA111BP Instrumentational OP Amps applications.
- High/low-pass filter circuit
- Hand-held batteries
- Commercial audio systems
- Tablets
- Strain gauges
- Television
- Video data acquisition
- Fission chambers
- Video computer boards
- Large motor controllers