INA126EA/250G4
| Parameters | |
|---|---|
| Package / Case | VSSOP |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 25.996513mg |
| Packaging | Tape and Reel |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 1GOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Instrumentation Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Pin Count | 8 |
| Number of Elements | 2 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 200μA |
| Max Supply Current | 200μA |
| Quiescent Current | 175μA |
| Slew Rate | 0.04 V/μs |
| Amplifier Type | INSTRUMENTATION AMPLIFIER |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 50nA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 200 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 80dB |
| Average Bias Current-Max (IIB) | 0.05μA |
| Power Supply Rejection Ratio (PSRR) | 106dB |
| Max Dual Supply Voltage | 18V |
| -3db Bandwidth | 0.2MHz |
| Min Dual Supply Voltage | 1.35V |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.005μA |
| Input Voltage Noise Density | 35nV/sqrt Hz |
| Voltage Gain-Nom | 100 |
| Height | 970μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
INA126EA/250G4 Overview
Packaged in a VSSOP case, the buffer op amp is ready to use. Op amps are INSTRUMENTATION AMPLIFIER types of amplifier on the chip. It comes in a Tape and Reel case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. In this case, there are 8 pins on the board. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. A type of Instrumentation Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are included on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 500μV. 80dB should be the voltage gain. The op amp ic has 1 channels on it. This op amp needs to be operated at a temperature of not less than -55°C degrees Celsius in order to function properly. You should not use op amp above 125°C . For the operating supply voltage of the op amp ic, there is a rating of 2. When it comes to the voltage from which this electrical part will operate, it can operate at a maximum of less than 36V. As a rule of thumb, the supply voltage of the op amp should not be lower than 2.7V. The dual supply voltage of 18V should be used for the conduct of this electronic component. Linear amplifier has a quiescent current of 175μA. During testing, the instrumentation amplifier resistance should remain within a range of 1GOhm.
INA126EA/250G4 Features
8 Pins
supply voltage of 15V
80dB voltage gain
Resistance of 1GOhm
INA126EA/250G4 Applications
There are a lot of Texas Instruments INA126EA/250G4 Instrumentational OP Amps applications.
- ECG equipment
- Radiation thermometry transducers
- Tablets
- Medical imaging
- Precision measurement
- Band-pass filter
- Vehicle electronics
- Voltage regulation circuit
- Industrial control system
- High input resistance broadband
