INA131BP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 528.605208mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Resistance | 10GOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | INA131 |
| Pin Count | 8 |
| Number of Circuits | 1 |
| Operating Supply Current | 2.2mA |
| Nominal Supply Current | 3mA |
| Max Supply Current | 3mA |
| Quiescent Current | 2.2mA |
| Slew Rate | 0.7V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 50μV |
| Bandwidth | 70 kHz |
| Gain Bandwidth Product | 70 kHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Average Bias Current-Max (IIB) | 0.002μA |
| Voltage - Input Offset | 10μV |
| -3db Bandwidth | 0.07MHz |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.002μA |
| Input Voltage Noise Density | 12nV/sqrt Hz |
| Number of Amplifiers | 3 |
| Voltage Gain-Nom | 100 |
| Non-linearity-Max | 0.002% |
| Voltage Gain-Max | 100 |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
INA131BP Overview
Packaging for the buffer amplifier is in the form of a 8-DIP (0.300, 7.62mm) case. An op amp of this type is a Instrumentation-type. The op amp is delivered to you in a Tube case. A total of 8 pins are located on this board. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. The buffer op amp includes 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 50μV. Through Hole is the recommended mounting type of operational amplifiers. With regard to operating temperature, this op amp functions well at -40°C~85°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 2.2mA and 10 . The buffer amp consists of 1 circuits in total. 2.2mA quiescent currents are flowing through buffer op amp. In order for the buffer amplifier resistance to remain within the 10GOhm range, the device should be tested. A total of 3 instrumentation amplifiers are present on the device.
INA131BP Features
8 Pins
supply voltage of 15V
Resistance of 10GOhm
INA131BP Applications
There are a lot of Texas Instruments INA131BP Instrumentational OP Amps applications.
- Displayers for aircraft and air transportation control systems
- Home audio systems
- Measurements of Wheatstone bridge
- Instrumentation
- Addition operation circuits
- Signal transformation
- Television
- Integrator circuits
- Industrial applications including automation
- Switching amplifier
