Parameters |
Lifecycle Status |
ACTIVE (Last Updated: 4 days ago) |
Package / Case |
SOIC |
Surface Mount |
YES |
Number of Pins |
14 |
Weight |
129.387224mg |
Packaging |
Tape and Reel |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Moisture Sensitivity Level (MSL) |
3 |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
60MOhm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Max Operating Temperature |
85°C |
Min Operating Temperature |
-40°C |
Subcategory |
Instrumentation Amplifier |
Packing Method |
TR |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Pin Count |
14 |
Operating Supply Voltage |
36V |
Number of Elements |
3 |
Temperature Grade |
INDUSTRIAL |
Number of Channels |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
9V |
Operating Supply Current |
10mA |
Nominal Supply Current |
12mA |
Quiescent Current |
10mA |
Slew Rate |
15 V/μs |
Amplifier Type |
INSTRUMENTATION AMPLIFIER |
Common Mode Rejection Ratio |
100 dB |
Current - Input Bias |
12μA |
Output Current per Channel |
60mA |
Input Offset Voltage (Vos) |
50μV |
Bandwidth |
800 kHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Voltage Gain |
80dB |
Max Dual Supply Voltage |
18V |
-3db Bandwidth |
800 kHz |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
15V |
Non-linearity-Max |
0.0006% |
Height |
1.75mm |
Length |
8.65mm |
Width |
3.91mm |
Thickness |
1.58mm |
Radiation Hardening |
No |
RoHS Status |
RoHS Compliant |
Lead Free |
Lead Free |
INA163UA/2K5E4 Overview
It is packaged in an SOIC-case that protects the operational amplifiers from damage. Op amps are INSTRUMENTATION AMPLIFIER types of amplifier on the chip. There is a Tape and Reel case that is delivered with the instrumentation amplifiers. The number of terminations approaches 14. In this case, there are 14 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. Instrumentation amplifier is a part of Instrumentation Amplifier. 14 pins are located on the operational amplifiers. Op amp ic rates 50μV for input offset voltage. An 10mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 80dB. There are 1 channels on the operational amplifiers. It should not lower than -40°C to operate buffer amplifier. A temperature greater than 85°C should not be used for the operation of buffer amplifier. There is an operating supply voltage rating of 3 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 36V. As a result of this, the buffer amplifier is packed in TR. In terms of the supply voltage, this electrical part is capable of operating at low voltage levels of under 36V. A high supply voltage of more than 9V is recommended for the instrumentation amplifier's supply voltage. As a rule of thumb, you should conduct this electronic part under a dual voltage supply of 18V volts. There is a quiescent current of 10mA in this operational amplifier circuit. Instrumentation amplifier resistance should stay within the range of 60MOhm.
INA163UA/2K5E4 Features
14 Pins
supply voltage of 15V
80dB voltage gain
Resistance of 60MOhm
INA163UA/2K5E4 Applications
There are a lot of Texas Instruments INA163UA/2K5E4 Instrumentational OP Amps applications.
- ECG equipment
- Strain gauges
- Differentiator circuits
- High-frequency data acquisition systems
- Integrator circuits
- Television
- Test and measurement instruments
- Non-polarized electrodes
- Wireless base stations
- Proportional counter tubes